The dlinkap.local is used as default dlink extender login domain address to access the web management interface or GUI of the D-link extender. It connects to the D-link extender on navigating through a web browser.

Can’t connect to Dlinkap.local?

Troubleshooting steps:

  • Ensure the Ethernet cable connected to the D-link wireless extender from modem to the WNA port is properly secure and not damaged.
  • Also, check if the Ethernet cable connected to the computer at one of the LAN ports is secure and not broken.
  • The D-link wifi extender must be powered on with its power status LED stable lit.
  • Disable all downloaded Anti-virus or malware software programs on your computer desktop because they might cause dlinkap.local login access errors.
  • Make sure you enter correct d-link extender login credentials to enter the web GUI page of the extender. 
  • Alternatively, try using D-link extender login IP address 192.168.1.1 instead of http://dlinkap.local which by default gets you through D-link extender login.
  • Make sure the d-link extender’s firmware has been updated to the recent version for better functioning as outdated firmware interrupts extender’s functioning and connect to dlinkap.local.
  • Try to reboot your D-link extender and source router, and then modem and computer by powering them off and turning them on after 1 minute. This might resolve minute errors in connecting to dlinkap local.
  • If none of the above helps, reset your d-link extender by pushing and holding the factory reset button to revert extender to default factory settings.

How do I log into my D-link extender?

  • Open a web browser on your computer adjoined to D-link wifi extender.
  • Access dlinkap.local web address from address field bar of the launched browser.
  • The dlinkap.local is default web address that routes to D-link extender Login page.
  • If the Login page shows login errors, access dlink extender IP gateway login by 192.168.50 IP address to access extender login page.
  • Enter the default D-link extender login credentials to log in to the Dlink extender web GUI.
  • Type admin as the default factory set d-link login administrative name and password or use the personalized password you might have assigned during Dlink extender setup.
  • Press Enter to login.
  • D-link login takes you to the web based interface of the extender to configure and manage extender network.

How do I connect my Dlink wifi extender?

D-link wifi extender could be connected to the existing source network for extending the wireless signals by following three methods:

  1. Connecting extender using D-link setup wizard 
  • Open a web browser on your computer adjoined to D-link wifi extender.
  • Access dlinkap.local web address from address field bar of the launched browser.
  • The dlinkap.local is default web address that routes to D-link extender Login page.
  • If the Login page shows login errors, access dlink extender IP gateway login by 192.168.50 IP address to access extender login page.
  • Enter the default D-link extender login credentials to log in to the Dlink extender web GUI.
  • Type admin as the default factory set d-link login administrative name and password or use the personalized password you might have assigned during Dlink extender setup.
  • Press Enter to login.
  • D-link login first time takes you to the Quick Setup wizard screen.
  • Access Quick setup wizard and perform step wise instructions by it to connect D-link extender to the existing network.
  • On prompting to configure the D-link extender, follow setup instructions and the wizard configures extender settings automatically.
  • Assign new SSID and password for extended network when asked, also create new dlinkrouter.local login password.
  1. Connecting extender using Web protected Setup (WPS)
  • Press hold the WPS button on the existing home network router.
  • Also, press hold the WPS button on the back panel of the D-link extender for 2 seconds.
  • The WPS led starts flashing on WPS functioning.
  • The D-link extender finishes setup after rebooting.
  1. Connecting extender using QRS app
  • Have the QRS mobile app downloaded and run on your phone.
    • Tap Setup extender option on the home page to begin setup connection.
    • Connect to the D-link wireless extender network.
  • The Quick extender setup page auto – launches to guide through connection setup and configuration of the D-link extender.

How do I access my Dlink extender?

  • Open a web browser on your computer adjoined to D-link wifi extender to access Dlink extender’s interface.
  • Access dlinkap.local web address from address field bar of the launched browser.
  • The dlinkap.local is default web address that routes to D-link extender Login page.
  • If the Login page shows login errors, access dlink extender IP gateway login by 192.168.50 IP address to access extender login page.
  • Enter the default D-link extender login credentials to log in to the Dlink extender web GUI.
  • Type admin as the default factory set d-link login administrative name and password or use the personalized password you might have assigned during Dlink extender setup.
  • Press Enter to access Dlink extender’s settings web GUI.

For any query Lets connected with us at https://dlinkextndersetup.com/dlinkap-local/.